Software

ASTM F2054 PDF

Posted On
Posted By admin

ASTM Standards. ASTM F ASTM F – Standard Test Method for Burst Testing of Flexible Package Seals Using Internal Air Pressurization Within. Consult Labthink Instruments Co., Ltd.’s High Pressure Leak Tester for Package ASTM F, ASTM F brochure on DirectIndustry. Page: 1/4. More help in interpreting the results can be found in ASTM F Inflation Seal Strength Testing (ASTM F and F), including burst, creep and creep-to-.

Author: Nelabar Faebar
Country: New Zealand
Language: English (Spanish)
Genre: Health and Food
Published (Last): 13 February 2013
Pages: 36
PDF File Size: 9.36 Mb
ePub File Size: 10.44 Mb
ISBN: 924-8-81325-285-1
Downloads: 68603
Price: Free* [*Free Regsitration Required]
Uploader: Kazilkree

MFY Leak Tester is used to look for pin holes in bags that hold calibration solutions for medical instruments.

Reference Appendix X3 for further information regarding calculation of stress factors and structural design considerations. Active view current version of standard.

ASTM F | Rycobel

Under Test Methods F the stresses are not distributed uniformly to all areas of the package seal. Test Methods F describes methods of burst testing that do not include the use of restraining plates and are suitable to determine a packages general ability to withstand pressurization stresses.

This test method cannot provide a measure of package seal uniformity. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use.

Product List | RDM Test Equipment | Assured Quality Testing Solutions

Historical Version s – view previous versions of 2f054. This test method should be combined with other methods of evaluating overall package integrity, uniformity of the package seal, or opening functionality, if so required.

Oxygen Permeability Tester to test containers. By placing the package within restraining plates during pressurization, the dimensional stability of the package is maintained in a manner that results in stresses applied more uniformly along the perimeter of the package, where seals are normally placed. Tensile Tester for both compression and tensile, with loads typically N.

  ASTM E384 PDF

Reference Appendix X3 for further information regarding calculation asstm stress factors and structural design considerations. In particular it is intended as applicable to packages with seals that have a peelable seal feature peeled open by end user to remove contents of package. Under unrestrained conditions the stress on the package is highest at the middle of the pouch where it inflates to the packages maximum diameter; therefore, Test Methods F may not reliably detect the weakest area of the seal.

Link to Active This link will always route to the current Active version of the standard.

An indicator of the minimum burst strength may satm of importance to the package manufacturer and end user in ensuring adequate package integrity. Seal Strength system to test 3 sides seal bags. See Appendix X2 for further information.

ASTM F2054/F2054M – 13

COF Inclined F254 Tester Measure the static coefficient of friction of various materials using a variable inclined plane and a sliding block. This test method provides an indicator of the burst strength of a package, where the burst will normally occur in one or more areas of the seal.

The Online Industrial Exhibition. Referenced Documents purchase separately The documents listed below are referenced within the subject standard but are not provided as part of the standard. This allows the test to have a higher probability of detecting the weakest area of the seal and provide a measurement of the pressure required to “burst” open the package.

  EM HAUPTKURS PDF

By placing the package within restraining plates t2054 pressurization, the dimensional stability of the package is maintained in a manner that results in stresses applied more uniformly along the perimeter of the package, where seals are normally placed.

This test method also cannot provide an evaluation of overall package integrity or the burst strength of areas of the package that contact the surface of the restraining plates used. See Appendix X4 for information. Labthink RT rub tester to test on flexo printing. Thickness micron testing equipment with Resolution 0. FT-F1 Fogging tester to to test for fogging on upholstery material and time frame for testing. Particular caution is advised where users of this procedure may be required to design and fabricate restraining plate fixtures.

Particular caution is advised where users of this procedure may be required to design and fabricate restraining plate fixtures. Flexible packages, aseptic packages, various plastic pilfer-proof closures, flexible tubes, caps and other materials. R2054 provides COF Tester for coef. Typical parameters can include, but are not limited to the package size, material, type and configuration of seal, rate of air flow into the package, pressure detection sensing mechanism and sensitivity machine response to pressure dropposition of test article, rigidity of restraining plates, and distance between restraining plates.

Specifications Test Range Contact: